Image

Livermore Lab researchers have developed a new EUV target design that replaces liquid tin droplets with tin microbeads embedded in a low Z tamping fluid. The use of low Z liquid tamped targets can solve several problems that are currently faced by the industry. It can increase the total operational uptime from 80% to close to 100%. It can simplify EUV source design and reduce…

Image
Livermore Lab researchers have developed two new methods for improving the efficiency of laser drilling. The first method is based on multi-pulse laser technology. Two synchronized free-running laser pulses from a tandem-head Nd:YAG laser and a gated CW laser are capable of drilling through 1/8-in-thick stainless-steel targets at a standoff distance of 1 m without gas-assist. The combination of a…
Image

Livermore Lab's SBC grating optics benefit from the combination of the following key technologies:

  • LLNL proprietary optical coating designs utilizing >100 thin film layers – enables ultra-low-loss, ppm transmission levels through the coating, high diffraction efficiency, and large bandwidth.
  • LLNL proprietary dispersive surface relief structure design –…
Image

LLNL researchers have invented a method for scaling the average power of high-energy solid-state lasers to high values of average output power while maintaining high efficiency. This method combines the gas-cooled-slab amplifier architecture with a pattern of amplifier pumping and extraction that is new to high-energy pulsed lasers, in which pumping is continuous and in which only a small…

Image

LLNL researchers have developed a method in which a sleeveless photonic crystal optical fiber cane can be fabricated. A set of glass canes and capillaries, doped or un-doped, are stacked into a hexagonal pre-form. A piece of outer tube which is much shorter than the pre-form, but longer than the "hot zone" of a draw tower furnace, is placed around the pre-form on either end, and crimped to the…

Image

Monolithic Telescopes are a novel implementation of a solid catadioptric design form, instantiated in a monolithic block of fused silica.

Image

The LLNL method for optimizing as built optical designs uses insights from perturbed optical system theory and reformulates perturbation of optical performance in terms of double Zernikes, which can be calculated analytically rather than by tracing thousands of rays. A new theory of compensation is enabled by the use of double Zernikes which allows the performance degradation of a perturbed…

Image

As diode pumped solid state lasers (DPSSL) become more common there is a need to drive these pump diode arrays in a compact, efficient and cost-effective manner. The LLNL system for controlling high current laser diode arrays is an integrated system for meeting the needs of driving laser diode arrays in a DPSSL. The system is comprised of technologies required to control the DPSSL that…

Image

LLNL has developed several MLD grating technologies that extend the state of the art in overall laser optical power handling capability. LLNL MLD grating optics are the convolution of the following key technologies:

  1. Optical coating designs utilizing >100 thin film layers - enables ultra-low-loss, ppm transmission levels through the coating, high diffraction efficiency, and…
Image

LLNL researchers have demonstrated a novel single-shot recording technology for transient optical signals in a time regime of picoseconds to nanoseconds for which currently there is a significant instrumentation gap.

The optical switching capability of optical semiconductors can be exploited in a pump-probe style architecture, where an auxiliary pump beam is crossed through the signal…

Image

LLNL researchers have developed a method for fabricating active or passive optical glass components, non-optical glass components, and/or glass sensors with custom material composition profiles in 1-, 2-, or 3-dimensions. In this method, DIW additive manufacturing technique is used to print filaments of a rheologically-tuned ink--containing a glass forming species--into a loosely bound,…

Image

Lawrence Livermore researchers have developed a novel waveguide with resonant leakage elements that frustrate guidance at well-defined and selectable wavelengths. Based on this waveguide, the LLNL team has fabricated a Large Mode Area Neodymium doped fiber with suppression of the four-level transition around 1060 nm, and demonstrated lasing on the three-level transition at 930 nm with good…

Image

Lawrence Livermore researchers are the first to successfully develop a practical fiber-optic amplifier that generates significant optical gain from 1,390 nanometers (nm) to 1,460 nm with relatively good efficiency. This discovery enables the potential for installed optical fibers to operate in an untapped spectral region known as the E-band, in addition to the C- and L-bands where they…

Image

LLNL is developing the Space-based Telescopes for Actionable Refinement of Ephemeris (STARE). STARE is a constellation of low cost nano-satellites (less than 5Kg) in low-earth orbit dedicated to the observation of space debris in conjunction with a ground-based infrastructure for maintenance, coordination and data processing. Each nano-satellite in the constellation is capable of recording an…

Image

The new LLNL technique works by transiently removing and trapping concrete or rock surface material, so that contaminants are confined in a manner that is easy to isolate and remove. Our studies suggest that 10 m2 of surface could be processed per hour. The technique easily scales to more surface/hr.

Image

This technology comprises a method of depositing coatings of dissimilar materials on a substrate. A laser pulse hits the film of deposited material covered by a thin water layer. The laser deposition on the water-material interface generates huge pressure accelerating film to the velocities a few hundred meters per second. The film hits the substrate at an oblique angle. The high velocity of…

Image

LLNL's Slurry Stabilization Method provides a chemical means of stabilizing a polishing compound in suspension at working concentrations without reducing the rate of material removal. The treated product remains stable for many months in storage.

Image

The selected industrial partner and LLNL will enter into a Cooperative Research and Development Agreement (CRADA) to develop the next generation of laser technologies for MEGa-ray systems and to create a next generation of MEGa-ray sources that could be marketed to both the industrial and academic communities.

The MEGa-ray system developed will be based on LLNL's proprietary, multi-…

Image

The SLIDER deflector includes a waveguide, a serrated mask positioned above the waveguide cladding, and a synchronized pump beam. The pump beam illuminates the serrated mask with a short pulse and transfers its pattern to the guiding layer where it imprints a sequence of prisms. The prisms are activated via nonlinear optical effects in the semiconductor and persist for the duration of the…

Image

LLNL's invention uses energy efficient diode arrays for softening metals and alloys to enable friction stir process and friction stir welding. The use of intense light from compact, light-weight, and energy-efficient diode arrays to preheat the material being processed to the softening point eliminates defects associated with insufficient weld temperature such as tunnel voids.

The…

Image

LLNL’s system consists of one or more flashlamp-pumped Nd:glass zig-zag amplifiers, a very low threshold stimulated-Brillouin-scattering (SBS) phase conjugator system, and a free-running single frequency Nd:YLF master oscillator.